• home

Audio Booster Circuit

Small and portable unit, Can be built on a veroboard

The amplifiers gain is nominally 20 dB. Its frequency response is determined primarily by the value of just a few components-primarily C1 and R1. The values of the schematic diagram provide a response of ±3.0 dB from about 120 Hz to better than 20,000 Hz.Actually, the frequency response is ruler flat from about 170 Hz to well over 20,000 Hz; its the low end that deviates from a flat frequency response.

The low ends roll-off is primarily a function of capacitor C1(since RIs resistive value is fixed). If C1s value is changed to 0.1 pF, the low ends comer frequency-the frequency at which the low-end roll-off starts-is reduced to about 70 Hz. If you need an even deeper low-end roll-off, change C1 to a 1.0 pF capacitor; if its an electrolytic type, make certain that its installed into the circuit with the correct polarity, with the positive terminal connected to Q1s base terminal.

Circuit Diagram:

Audio_Booster_Circuit Diagram Audio Booster Circuit Diagram

Parts Description
P1 100K
R1 47K
R2 470K
R3 10K
R4 560R
R5 270R
C1 0.1uF-25v
C2 3.3uF-25v
C3 470uF-25V
D1 5mm. Red Led
B1 9v Battery
J1 RCA Audio Input Socket
J2 RCA Audio Output Socket
S1 On-Off Switch

 

Source :www.extremecircuits.net

Hydrophone Booster Amplifier HA2

Hydrophone Booster Amplifier (HA2)

The HP series Hydrophone Booster Amplifier (HA2) amplifies low-level hydrophone signals over a wide range of frequencies. It has a minimum gain of 25dB and an input and output impedance of 50Ω. The HA2 is designed for use with either Precision Acoustics membrane hydrophone or Precision Acoustics HP Series Hydrophone Measurement System, which is shown in Fig 1.

Hydrophone Booster Amplifier 

Alternatively, the HA2 may be used when the acoustic signal is provided by a high output impedance hydrophone, such as a GEC-Marconi membrane device, or a conventional hydrophone. In this instance a BNC/MCX adaptor is used which connects directly to the HP Series Submersible Preamplifier, using it as a buffer amplifier, (i.e. the standard Precision Acoustic HP Series configuration shown in Fig 1 is used, but without the interchangeable probe).

The HA2 amplifier is straightforward to use but the following points should be noted:

  • The output of the amplifier should be correctly terminated in 50Ω before operation.
  • The HA2 amplifier is non-inverting but this is of no consequence when used with the HP Series interchangeable probes as their design takes this into account. However when a submersible preamplifier is used as a high impedance buffer amplifier (as in Fig 2) the system output from the HA2 will be inverted as the HP Series Submersible Preamplifier is inverting.

Before Connecting the unit please read WARNING

To Connect

To  Disconnect

1 Connect Output Load 1 Remove RF Input
2 Apply DC Voltage 2 Remove DC Volts
3 Apply RF Input 3 Remove Load

Specification (HA2 Amplifier Only)

Voltage Gain = 25dB minimum
Bandwidth =  50kHz to 125MHz ±1.0dB
Maximum Output Level = 29dBm for 1dB compression (18.1V pk – pk into 50Ω load)
Input Impedance = Nominal 50Ω
Output Impedance  Nominal 50Ω (VSWR 2:1)
Output Noise Level = Typically 70μV pk – pk (bandwidth 125MHz)
Noise Figure = Typically 10dB
Phase = Non-inverting
Terminations:
Front panel = Input BNC socket BNC Output socket
Rear panel Power Requirements = 28v dc output to supply DC Coupler 100/120/220/240V ac, 50 to 60Hz,
7.5W
Operating Temperature = 0 to 50°C
Size = (90mm × 205mm ×194mm)
Weight = 2.6kg

Copyright : Precision Acoustics March 2004

15dB UHF TV Antenna Booster Circuit

15dB UHF TV Antenna Booster Circuit15dB UHF TV Antenna Booster Circuit

This is an UHF bandage TV antenna preamplifier circuit With 15dB accretion to body easily. It is formed based on BF180 UHF Transistor. The aboriginal date is an bandage canyon clarify complete by the C1, CV1, L1, L4, C7 and C3, the additional date is a base-common voltage amplifier with low ascribe impedance to match. Body the L1 ~ L4 as air amount braid to access aerial Q-Factor. After assembling, backpack it into a able brownish box and affix the arena of the ambit to the box to abate babble effect.